Septic systems are most often found in rural areas of 97068 and will consist of a series of pipes connecting it to the home, a septic tank, a filtering system to separate the solid waste from the liquid and connecting pipes that drain off the liquid waste into the yard, in a designated area called the drain field. These systems are often inspected before septic installation and tested afterwards, to make sure that it is operating properly.
Ownership of a septic tank system in 97068 means that everyone understands the importance of having regular septic tank inspection and septic pumping to catch potential problems before they happen. All too often, nothing is done until the worst happens, like the tank developing a leak, or it backs up into an area away from the drain field. Two easy ways to avoid this from happening include monitoring what goes into it as waste and remembering its physical location to avoid accidents.
When there is a septic system installation, the area where the septic tank is placed should be noted so that no accidental driving or parking of a heavy vehicle can occur. While most tanks are buried deep enough to avoid this, as a general principle it should be avoided to prevent damage to the tank in the future.
What are the health department regulations for a Septic Tank in 97068?
Regular septic tank inspections done by a professional plumber can help avert a major disaster caused by a septic system failure. Unfortunately, these are more common than you would think. Because the septic system runs underground, most homeowners tend to ignore it. However, failure to carry out regular inspections of the sewer system can be a health hazard and can also result in destruction of the surrounding property.
Before buying a new home, it is crucial to find out as much as you can about the system. Find out how old the system is and whether or not is has been regularly maintained. Better still, get an inspection done so that you do not start having problems as soon as you buy it and shift in.
What Causes Failure Of The Septic System?
There are several different factors that may cause the septic system to fail. Some of the more common reasons include:
• The septic tank is too small
• The diameter of the drainage pipes are too small
• The drainfield is not large enough or it may not leveled correctly
• The soils in which the system is installed is unsuitable
• Tree roots have entered into the pipes and are causing a blockage
• Faulty surface drainage
The problem is, more often than not, by the time the homeowner realizes there is a problem the damage done would already be quite extensive. To make matters worse, without the proper knowledge and equipment it is almost impossible to determine the cause of the problem. Leaving it unattended or trying to contain the damage by trial and error will only make matters worse. The only way to prevent extensive damage is by calling in a professional to try and resolve the issue.
How Septic Tank Inspection and Maintenance Is Done
When you call a professional plumber to inspect the septic tank and carry out the necessary maintenance, they will come with all of the latest tools.
First they will test for a blockage or seepage by using a sewer camera or by the fluorescent dye method. After determining the exact cause of the problem, they will then use the correct tool to correct it. A sewer snake is usually used to clear a stubborn blockage if that is what is causing the problems. A sewer snake, also called an electric eel, is a long, slender and flexible pipe that is sent into the drain pipe. Though flexible and slender, the pipe is tough enough to dislodge the clog. If the blockage is caused by tree roots that have invaded the pipe, these are usually cut by using a specially designed device called a drain rooter.
Septic tanks help dispose of the dirty water from the house and purify it. However, for a septic tank to function efficiently, it must be maintained properly so that you do not have to suffer from clogged drains and a leaking plumbing system. Septic tank risers will help you have easier access to the area so that you can keep a check on it when necessary and also locate it easily.
Different Types of Septic Tank Risers
A septic tank riser will vary in size depending on the size of your tank. You will usually need one that is between six inches and twelve inches long with a diameter of twelve to twenty-four inches. If the container is buried deep underground, these devices may have to be stacked on top of each other.
There are three kinds of risers that you can purchase depending on the material that is used to make them.
The first and most basic option available is a concrete riser. This is usually quite heavy and it can be a little difficult to install. Concrete also suffer a lot of wear and tear so you may need to replace it often. This means that even though it is the cheapest option in the market, in the long run you may end up spending more because you will have to replace it more often than the others.
The other two options are PVC and Polyethylene risers. These are a lot more durable and they look better than the concrete ones. They are also lighter so it is easier to get them fitted to the tank. During their installation, gaskets are used in order to seal them. This makes the lids fit more securely and it prevents outside matter from getting inside the area. PVC and Polyethylene is also non-reactive to other chemicals so they don't get damaged easily and you will have to replace them very rarely.
Why Get a Riser?
A septic tank riser has two basic functions. First, it helps you locate the area. Even though this may not seem important, locating the container can often get difficult, especially when it is buried deep underground. In fact, building regulations now make it compulsory to install these accessories for all septic tanks that are located in the premises of the building. The other important function is to help you lift the lid of the container. Since these tanks are fastened securely and held down by steel screws, it can get very difficult to lift the lift without a riser. In fact, some risers are even made with structural ribs so that frost does not build on them and they can be used easily during all weather conditions.
Do you know where your septic tank is? Okay, so you can point to an area on your property and say "yeah, it's over there" with a hint of un-sureness. The next question is probably more important then the one just asked. Do you know where the lid to your septic tank is? Does that have you scratching your head?
Septic tanks by their very nature are buried, sometimes 3 feet or deeper underground. Out of sight out of mind so to speak. But that's not necessarily a good thing. There will come a time when your septic system begins to exhibit problems and needs some maintenance/repairs and the tank needs to be pumped out. Having a general idea as to the location of your tank can make getting this simple task done much more difficult.
There are two ways to deal with this problem and one way to make sure that in the future it won't be an issue. First let's look at finding the lid to the septic tank if you don't know where it is. You can either dig for it yourself or have the septic pumping service do it. Doing it your self can be time consuming and not a lot of fun. Having the pumping service do it can be costly.
Generally it is done in this fashion. You or someone you hire has to dig down until they find the top of the septic tank. That is usually the easy part of the process. Once you find the top of the tank you then need to find the lid. This can involve digging concentric circles outward from your initial hole until you find the lid. Once you find the lid now is the time to fix the problem; install a riser.
A septic tank riser is essentially a large tube that extends from the lid of the tank up to the surface of the ground. Once installed it will provide quick access to the septic tank that's easy to find any time there is a problem or it needs to be pumped out.
There are three basic types of risers to choose from; concrete, PVC, and polyethylene.
While concrete risers are generally cheaper it isn't the best choice. A concrete riser is heavy and may need heavy equipment to lift and install it. It is also more apt to leak then the other materials and may have rust problems if rebar is used to strengthen the cement.
PVC and polyethylene risers are lightweight and easy to install. They are resistant to corrosion and of course will not rust. They also incorporate a gasket seal to keep water from entering and prevent sewer gases from escaping from a leaky lid. The increased cost of these two types of risers is well worth it. They are virtually maintenance free and will easily last for the life of the whole septic system.
Every septic tank needs a riser and in many places they are now a code requirement. If you don't have one it might be worth having one installed before something goes wrong with your septic system. Quick access to the tank is one of the first steps to diagnosing any problems.
If you live in an area that uses septic systems for waste water disposal, from Portland, Oregon to New York City to Dallas, Texas to Miami, Florida, then I know you have known people who have had to either replace their septic systems or have had to make significant repairs to them. These were, I am quite sure, extremely expensive episodes for the home owners. Suffice it to say that septic system failures are not only expensive to repair or replace but the cleanup is also very costly as well as unsanitary. Hence, septic tank pumping should be a priority in your home maintenance routine.
How Often Should the Tank be pumped?
The experts recommend that septic tanks be emptied and the entire system inspected periodically. The frequency of this service is dependent upon several factors:
Size of the tank: this is pretty much self-explanatory. It follows that if you have a small tank, it will need to be pumped or emptied more often.
Amount of waste water processed: this factor is dependent upon the number of people who live in the home and how much water each of them use. One of the factors within this category includes the age of the toilets in the home. If you have a home that is more than 20 years old, it is likely that you will have the original bathroom fixtures and those fixtures may not be water efficient. The older style toilets require 3 to 5 gallons of water per flush, while the newer, more efficient models only require 1.5 or gallons per flush. There are also "dams" that can be placed inside the toilet tank to reduce the amount of water used per flush.
Where does the money saving come in?
Having your septic tank pumped (emptied) regularly can save hundreds of dollars in repairs, replacement and cleanup. The experts recommend that most systems be inspected and pumped about every 3 to 5 years depending on the above mentioned factors. When the septic service company comes to do the pumping, they will also inspect the system for leaks in the plumbing coming into and leaving the tank, the drain field and valves and filters in the tank. If damage or wear is noted on any part of the system, they can alert you so that plans to make the repairs can be made before the failure occurs. Preventing the failure of your system by periodic inspections and septic tank pumping will save money on major repairs and replacement as well as the cleanup process should a failure occur
If you have a septic system, then you are familiar with the term septic tank pumping. For those of you who do not know what a septic system is, it is an underground sewage system for household waste. It is not connected with the main sewage system. These systems are usually found in the rural areas.
So how does a septic system work? It is made up of four parts; the septic tank, the pipe that is connected to the house, the soil, and the drain field. From these four components, the septic tank is the most important, and needs a lot of maintenance. But, damage in any of the parts will cause the system to malfunction. This further leads to heavy repairs.
If you do not maintain the system you may face many problems like:
1. The tank may get clogged and begin to give off a disgusting odor. This happens when a lot of cooking oils and grease enters it, this blocks the inlet drains. These are very hard to degrade.
2. Most people who have septic systems fail to remember that all wastes are not biodegradable. Waste like paper towels, cigarette butts, sanitary towels, and cotton ear buds do not disintegrate. They enter the tank and clog it up.
3. You need to check the tank regularly for any cracks and damages. If you do detect any, you should get them repaired immediately.
To avoid these problems, you could have the tank pumped regularly. There are plenty of agencies that provide you with this service. They are quite easy to find if you look up the internet or the newspapers.
So what is septic tank pumping? Large tanks with suction pumps are used to pump out all the sludge and scum that has accumulated over time. The waste is sucked into a tank that is on the truck. Proper methods are later used to dispose of the waste.
It is important that the tank is pumped regularly. It ensures the smooth functioning of your septic system. It helps to keep your tank clean too.
The agencies that provide this service also provide other services for your septic system. You could employ them to come and perform regular checks. It will take the hassle of your hands.
In rural areas, you can find these septic tanks in almost every house. Septic tank is very essential in such locations to collect the sewage waste from house. Most of them install a tank with great care, but lack in maintenance. Effective maintenance of septic tank avoids many issue and future and cut downs the cost of septic services like cleaning and pumping.
Maintenance of septic tank is not a tough job and it requires simple precautions in dumping waste etc., to avoid major problems like repair and replacement of leachfiends, one should follow few simple steps of septic maintenance. Every contractor or a well-trained professional will suggest the first most common thing is to "Conserve Water".
Increase in the level of waste water will cause frequent cleaning and pumping activities of a container. So, reduce the usage of water, this can help in cutting down the cost. Avoid dumping heavy solid waste materials into the container. These solid wastes will cause severe damage to the septic system. They cause blockages or clogging in the drainfield that leads to repair or replacement.
Reduce the usage of chemical substances like cleaners as they kill the bacteria inside the tank. The bacteria are very useful for breaking the solid sludge to smaller particles. All these activities can help in cutting down the cost of septic tank cleaning and pumping.
One should pump out their tank at least once in a year. This depends on the number of people staying in the house, and usage of waster. The cost of pumping is not so costly. Contacting a right service provider can assist in performing the job successfully. In general, pumping a tank cost around $75 to $200. Pumping out larger containers will cost around $200 to$350 or more. If you would like to replace or install the new high-quality filter to protect your leachfield then, the cost would be $200 to $300.
While renting a cleaning and pumping service provider, you must be very cautious. Rent a professional service provider and make sure that you ask all your doubts on cleaning and pumping activities. Don't forget to ask about the discounts and offers in their company. Knowing about the offers can save you handsome amount of money. There are some companies that charge less than the cost provided above. But make sure you are electing a nice company for an effective service to your tank. The above specified costs are not constant in every company. They may vary according to the vendor and location.
Septic Tank Inspection Oregon